You Sure it Will Make it out of the Basement

Before totally committing to building a boat in the basement, one needs some kind of proof its not going to be Noahs ark waiting for the basement to flood to get some use. While the tape measure said it would make it out...I wasnt sure that I wasnt another idiot building a big project that was stuck in the basement. I have to make a slight turn at the top of the stairs to clear the kitchen cabinets, so its not a straight shot out of the top of the stairwell.

My first plan was to temporarily set up the frames, transom, stem and keel and then fashion some temporary plywood sheers and take the clamped together skeleton on a trial run. But my son Bill said maybe a tricked up 4x8 sheet of plywood would suffice. Not wanting to remove frames from my set-up form it sounded like a good idea. So some temporary plywood strips were used to simulate the shape of the shears, traced onto scrap plywood and cut to shape. These were screwed to the stem and breasthook assembly which was screwed/clamped to a 4x8. The stem and various bar clamps were used to simulate full beam width of the boat and depth of the boat. The trial run into the stairwell and out at the top went with no issues. I took some clearance measurements at the tight spots and I have some room for more length, beam, and depth....but not enough to change plans to a bigger boat and start all over!

The kitchen in the background was a major project of a few years back. My son and I built all the cabinets, doors, drawers, etc. Maybe it will be another blog someday.

Read More..

What happens if you make a mistake

Are you scared to start a boatbuilding or other project in case you mess up, in case you make a mistake? What will people say, will your friends joke about it and embarrass you?

Nearly everyone makes mistakes. Those who say that they dont make mistakes are either lying or are not pushing the boundaries of their own ability. As long as we are trying new things, taking on new life experiences, we will make mistakes. It is an essential part of the whole learning experience. Sure, it is nice to learn from the mistakes that are made by others but we learn more lessons, we learn them faster and the message sticks better when we make those mistakes ourselves. The more painful the mistake, the stronger the lesson that we will learn.

When I designed the Paper Jet, I had a particular building procedure in mind for the boat. As it turned out, the Paper Jet could not be built the way that I had envisaged. So, I had to go back a few steps and think of a different way to assemble it. I did that and went ahead and built my boat by a different method. I had a few other smaller backtracks and eventually had my boat complete.

Did I make some mistakes? Yes I did but so what? I made those mistakes because I was doing something that I had never done before. I was doing something that nobody had done before. I needed to learn the lessons that had to come out of building this prototype so that I could write the building instructions in the best way that I could, to enable other builders to get it right without making those same mistakes.

If I was scared of making mistakes I would not be trying new things. I designed and built the first radius chine plywood boat, my own "Black Cat", and made some mistakes along the way. Every time I was able to recover the situation very quickly and move on to the next stage of building. Overall, the project was a great success. Along the way I shrugged off the comments and criticisms of others because they were of no consequence unless I allowed them to be. They were generally from people who have never built anything major themselves. It is normal that the people who will laugh when someone makes a mistake are those who dont achieve much themselves. Disregard those people.

While building "Black Cat", one evening I was working with a spindle router shaping some small plywood parts. I was annoyed about an interruption unrelated to what I was doing and which had broken my concentration. In my distracted state of mind, I put my right thumb through the router bit, which was spinning at 20,000rpm. It made 11 cuts to the bone in the space of 1/2" and I was spraying blood. Within a minute or two I was passing out from pain and shock and was hauled off the the doctor. She said she had never seen such neatly done damage to human flesh and described it as sliced like deli meat. She was able to fix it with one stitch threaded through all of the slices. The worst impact from my mistake was a couple of weeks knocked out of the middle of my already tight building schedule.

OK, so we all make mistakes. Hopefully most of them will be to your boat rather than to yourself. How do you recover from your mistake? First you need to know what your mistake was, i.e. what it was that you did and what you should have done differently. That should help you to figure whether or not you can take apart the incorrect work. If you can take it apart then do so and rebuild it correctly. If you cant take it apart then you must figure the best way to modify the structure to correct it.

When you buy a set of quality boat plans you get access to a support system as part of the package. That includes being able to ask the designer for advice when needed and to steer you along the best path whenever you have a problem. You may think of a way to correct it but the designer, from past experience, may be able to offer some other alternatives and to say what will be best. It is likely that the designer or someone else has made the same mistake before.

The important things to understand are:-

1. You will occasionally make mistakes.
2. Some of those mistakes will be silly ones and may embarrass you. Laugh them off. Take control of the situation and correct it, dont allow the mistake to take control of you.
3. The designer of your boat should be available to help. Contact him, explain your mistake and ask for advice.
4. You can recover from most mistakes. It may take a bit of application on your part but you can do it.
5. When your boat is finished you will know where your mistakes are but most other people will never see them.

When prospective builders tell me that they could not build to the standard that they see in my Paper Jet, I sometimes point out some imperfect workmanship so that they can see that my work, like theirs, is not perfect. We all make mistakes. Fix them, then get on with life.

Read More..

Would you like a pleasant alternative to Black Friday

 
You may not know about Chincoteague...

but, its a place near and dear to our hearts. If you are trying to avoid the mass hysteria of "Black Friday", I recommend that you consider a trip to Chincoteague, Virginia instead.

Years ago, when we started to go to "carving" shows, many of our friends and colleagues, in particular, the late great Lee Scheely, told us: "Youve got to go to Chincoteague!". The way it was put made the show a bit intimidating. We didnt know if we could even get in, especially where our subject is boats, rather than birds. There is, however, a good deal of carving that goes into our work and so we started "doing Chincoteague". It may have been one of the best things weve done.

There are actually three of the Chincoteague carving shows each year: Thanksgiving, Easter and Labor Day. Weve never been able to do Labor Day for unrelated reasons. Weve discussed the Easter show on our Facebook page. This weekend (Friday & Saturday Nov. 25th & 26th) is the Thanksgiving show. Its also a Christmas show.

Let me tell you about these shows. They are held at the Chincoteague Combined School in its gymnasium. No huge signs out front. You might think that youre looking at a Holiday Bazaar or other Craft Fair when you only look at the outside of the building. A school with a lot of vans and trailers parked outside. Sounds like a bunch of amateurs???

When I first came to these shows, I was blown away. The exhibitors represented the Masters Masters of carving, many that I knew from Havre de Grace and The Waterfowl Festival and other great nationally recognized shows. Among them were Bill Veasey and Shannon Dimmig, Vince Ciesielski (I probably spelled his name incorrectly), Bill Cowen, Jennifer Daisey, Russell Fish, Walt Schmitz, Bill Hickson, Rocky Detwiler and scores of other truly great carvers. The painters and sculptors were no less amazing. Other artists, such as Donnie Thornton and Don & Donna Drew really rounded the shows out nicely. There is no room to mention many of them, no less to describe their work.

What was also amazing was to find such a low key atmosphere, where you didnt just have the opportunity to see some amazing art and artistry, but the opportunity to spend time talking with the artists and getting to know them. Over the years, weve made a lot of friends and weve learned a lot of things from being in the Chincoteague carving shows. Unfortunately, weve lost more than a few of those friends over those years, such as Lee, Don Repsher and some others who we came to expect to see when we arrived and now really miss. We were lucky to have the opportunities to learn from them and to be able to call such great people our friends.

These shows have changed over the years. Everyone used to know about them - they were legendary. Word of mouth has been overcome by electronic media and low budget shows cant buy the advertising that the large retailers can. The Deborah Waterfowl Show and Auction is a truly great show with truly great carvers and artists of many kinds. Its an honest display of high quality things, in some cases among the best in the world of those things.  They are reasonably priced and made with precision and care. If you are looking for gifts, you will be amazed at what awaits you.

As you consider the idea of patronizing small businesses, I recommend that you consider this show, full of hard-working people, who, although they may not be immediately recognized as such, are small business owners. Proceeds from the show benefit the Deborah Heart & Lung Center in Browns Mills, NJ. As with the eggs that we carve for the silent auction at the Easter show, we apply our talents to wooden balls such as the one below. Come to the live auction on Saturday night to get your hands on some very special things...

The show is only a small reason to come to the island of Chincoteague. Its a beautiful town with shops, restaurants, hotels, B&Bs and beautiful views. The Wildlife Refuge opens up miles of road that are only open for Thanksgiving weekend. You can see the famous ponies (dont tell me that youve never heard of "Misty of Chincoteague"), Snow Geese, deer, beaches and... Ive told you enough.

Again... Avoid the Malls! Come to The Deborah Waterfowl Show and Auction, Friday and Saturday, November 25th & 26th, 2011 at the Chincoteague Combined School in Chincoteague, Virginia. For more information call (757) 336-6161

Read More..

The More You Know The Less You Know

I was reading a forum item about water up the rudder stock tube.  This was something I had never considered or been told about although on very hard reverse on my NB I would get water up the tube.  I just put this down to poor design because of its age.  When the water came up it just ran off the self draining read deck, but on this boat its going to go into the engine room bilge.......... Not good.

As I hadnt considered this I needed to work out how to retrospectively fix it.  Much head scratching and I came up with this idea.

I disassembled the rudder, ram and removed the stock.

I then slid a length of PVC pipe over it having first coated the shaft with silicone grease.

I reassemble the rudder and stock then filled the gap between the stock tube and the PVC tube with closed cell expanding foam.

Once cured I trimmed off the excess.

I think this will solve the problem.

Read More..